ccna 200 301 syllabus of errors pdf to excel

ccna 200 301 syllabus of errors pdf to excel.Router>en Router#conft Router(config)#host R1 R1(config)#no cdp run R1(config)#int sl/1 R1(config-if)#ip add 12.1.1.1 R1(config-if)#noshut R1( config-if)#intfa 0/0 R1(confia-if)add 21.1.1.1,255.255.0.255.255.0 R1(config-if)#no shut R1(config-if)#intloO R1(config-if)#ip add1.1.1.1 255.255.255.0 R1 (config-if)#intlol R1(config-if)#ip add3.3.3.3 255.255.255.0k206 ^7E[GRP^ 07R1(config~if)#router eigrp100Enable the ETGR2 routing protocol process ,EHGRP and worker GRP are the same ,use the AS number ,here 100 is the AS number . The AS identifies a unique autonomous system number , which identifies all routers belonging to an interconnected network. In order to ensure that different routers can learn routes from each other, different routers within the same AS should use the same AS number. This is different from the RMF protocol configuration, which does not require the use of AS numbers. R1(config-router)#network12.1.1.00.0.0.255 Here 12. "0 is the network number, 0.0.0.255 is the reverse mask, Cisco documentation called w to dc&rd mask, translated into Chinese is a wildcard mask, this call is inaccurate, more accurate call is called the 3 eyes of a subnet when the symmetry The mask (reverse subnet mask, referred to as the inverse mask ). The network number and the inverse mask together determine which interface of the router to participate in the E worker GRE, as well as the router to which network announcements. If the inverse mask is omitted, the primary class network number is automatically used in the comet. If the router has two interfaces, one with a billet address of V72.2,1.1/24 and the other with an IP address of 172.16.2.1/24, where the 172.16.2.1 interface does not run the EIGRP protocol, it cannot simply write n&t work 172.16.0.0, '^^^172.16.1.0 0.0. 0.255, so that the network declaration does not include the network of V72.16.2 *0/24, detecting 2.16. 2 summoned interfaces do not participate in the E1GR2 process. In the topology shown in Figure If-2, here can be written as eye seven work 12.0.0.0. This is in addition to the main class network number and subnet number can be used in addition to the super network, for example, the router has two interfaces, an interface work 2 address is 172.16.1.1/16, the other interface is the current address is simply a network 172.0. 0.0.00.255.255.255.255 command to announce the two primary class networks. If the router is running EEGRB on all interfaces it can simply be written as network 0.0. O.Or Router R2 uses this command. gtwork 0.0.0. 0 is not used on Router R1 because R1 has - one interface that is not running ETGRP, that is Loopback 1.R1(config-router)#network 21.1.1.0 0.0.0.0.255 R1(config-router)#network 1.1.1.0 0.0.0.0.255Router>en Router#conft Router(config)#host R2 R2 (config}#no cdprun R2(config)#int sl/0 R2(config-if)#ip add 12.1.1.2255.255.255.255.0 R2(config- if)#noshut R2(config-if)#intfa 0/0 R2(config-if)#ip add 21.1.1.2255.255.255.0 R2 (config-if)#no shut R2 (config-if)tintloO R2(config-if)#ip add 2.2.2.2255.255.255.0 R2(config-if)#router eigrp 100 R2(config~router)#network 0.0.0.0Use the following command to view the interval at which the router R1S1/1 interface sends Hello packets.