cisco 200-301 volume 1 vs volume 2

cisco 200-301 volume 1 vs volume 2.192.168.2.0, which is connected to interface s0.4. Go to router 2600-2O and click the tab Lab Instructions and select 2600-2 from the drop-down list Devices; you can also click the tab NetMap and double-click the device icon 2600.2.5. On router 2600-2, verify that interfaces faO/O and s0 are enabled; if they are not, enable them. Check the IP address configured for Router 2600-2±. On router 2600-2, use the command show interfaces to view the configuration. If interfaces faO/O and s0 are not in the knock state, go to those interfaces and enable them with the command no shutdown. Use the command show interfaces to verify that the IP addresses configured in Chapter 15 are still present.6. View the routing table for router 2600-2. Execute the command show ip route, and you should see two directly connected networks: 192.168.3.0 connected to interface fhO/O and 192.168.2.0 connected to interface s0.7. Check the connectivity between Host-1 and Router 2600-1. Click the tab Lab Instructions, then select Host-1 from the drop-down list Devices; you can also click the tab NetMap, then double-click the device icon Host-lo on Host.l, ping router 2600-1: ping 192.168.1.1, this ping operation should be successful; if it fails, it is possible that you are using the configuration from the VLAN experiment in Chapter 12 and there is a VLAN configuration problem in it. 8. Check the connectivity between Host-3 and Router 2600-2. Click the Lab Instructions tab, then select Host-3 from the drop-down list Devices; you can also click the NetMap tab, then double-click the Device icon Host-3o on Host-3, ping Router 2600-2: ping 192.168.3.1, this ping operation should be successful. 9. Check the connectivity between Host-3 and Host-1. On Host-3, pingHost-1: ping 192.168.1.10o This ping operation should fail because Router 2600-2 does not have a route to Host.l.10.Check the routing table on router 2600-2: Use the command show ip routeQ does not list 192.168.1.0/24.11. On router 2600-2Ji, configure a static route to 192.168.1.0/24 (which is connected to router 2600-1). Click the LabInstructions tab, and then select 2600-2 from the drop-down list Devices; you can also click the NetMap tab, and then double-click the device icon 2600-2o configure a static route to 192.168.1.0/24 via router 2600-1: execute the command configure terminal in order ip routel92.168.1.0 255.255.255.0 192.168.2.1 and endo12. View the routing table for router 2600-2. To view directly connected routes and static routes: execute the command show ip route. confirm that 192.168.1.0/24 appears in the routing table as a static route(s). 13. on router 2600-1, configure a static route to (connected to) 192.168.3.0/24 on router 2600-2. Click the LabInstructions tab, and then select 2600-1 from the drop-down list Devices; you can also click the NetMap tab, and then double-click the device icon 2600-1o configure this static route: execute the commands configure terminal, ip routel92.168.3.0 255.255. 255.0 192.168.2.2 and endo 14. View the routing table of Router 2600-1.To view direct and static routes: execute the command show ip routeo to confirm that 192.168.3.0/24 appears in the routing table as a static route(s).15. ping the interface faO/O of router 2600-1 from Host-3. click the tab LabInstructions, and then select Host-3 from the drop-down list Devices; you can also click the tab NetMap, and then double-click the device icon Host-3o enter Host-3, and ping the interface of router 2600.1 faO/O: ping 192.168.1.1, this ping operation should be successful.