ccna 2 chapter 8

ccna 2 chapter 8.out bytes 5594 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out beast pkts 45 out beast bytes 3030 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 00. 39:49, last time pvc status changed 00:27:29 DLCI = 53, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = SerialO/1/1 input pkts 64 output pkts 82 in bytes 4206 out bytes 6612 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out beast pkts 38 out beast bytes 2532 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec pvc create time 00:33:49, last time pvc status changed 00:27:19 DLCI = 54, DLCI USAGE = UNUSED, PVC STATUS = ACTIVE, INTERFACE = SerialO/1/1 input pkts 0 output pkts 0 in bytes 0 out bytes 0 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out beast pkts 0 out beast bytes 0 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate bits/sec, 0 packets/sec pvc create time 00: 00 59, last time pvc status changed 00:00:59 Atlanta# show frame-relay mapSerial0/0/0.3 (up): point-to-point dlci, dlci 54(0x36,0x060), broadcast status defined, active14.2 Basic Content 301Example 14-12 (continued)SerialO/O/O.2 (up): point-to-point dlciz dlci 53(0x35,0xC50), broadcast statusdefined, active Serial0/0/0.1 (up): point-to-point dlci, dlci 52( 0x34,0xC40), broadcast statusdefined,, activeAtlanta# debug frame-relay Imi Frame Relay LMI debugging is on Displaying all Frame Relay LMI dataSerial0/0/0(out): StEnq, myseq 163, yourseen 161z DTE up datagramstart =0x45AED8, datagramsize =13 FR encap = 0xFCF10309 00 75 01 01 01 03 02 A3 AlSerial0/0/0(in): status, myseq 163 RT IE 1, length 1, type 1 KA IE 3, length 2, yourseq 162, myseq 163The showframe-relaypvc command lists useful management information. In particular, the output includes the number and percentage of various packets passing through each PVC. In addition, PVC status is an important entry point when troubleshooting.The showframe-relay map command lists mapping information. For the previous full mesh interconnection example, the configuration does not use any sub-interfaces and lists only the Layer 3 addresses using each DLCI. In this example, a DLCI is shown in each entry, with no mention of the corresponding Layer 3 address. And while the full mapping point is to associate a Layer 3 address with a Layer 2 address, no Layer 3 address is shown at all in the output of the fhame-relay map command! The reason is that the point-to-point subinterface router can discover the correct mapping information from the local configuration, as follows.