ccna ka full form

ccna ka full form.Rl(config)#ipv6 unicast-routing Start IPv6 unicast routing Rl(config)#ipv6 route::/0 serialO/O/1/// Configure IPv6 static default route Rl(config)#ipv6 router ospf1 Start 0SPFv3 routing processR1 (config-rtr)#router-id 1.1.1.1 Configure 0SPFv3 router ID, if it is a pure IPv6 environment, it must be configured explicitly Rl(config-rtr)#auto-cost reference-bandwidth 1000/// Modify the calculation of Cost reference bandwidth R1 (config-rtr)#default-information originate metric 30 metric-type 2 Inject a default route into the OSPFv3 network with an initial metric value of 30 and a type of 0E2 (default) RI (config-rtr)#exit.320.Cisco Networking Lab CCNA Lab Guide (Release 2) R1 (config)#interface Serial0/0/0 R1 (config-if)#ipv6 address 2017:1212::l/64Rl(config-if)#ipv6 ospf1 area0 Enables OSPFv3 on the interface, and declares the area where the interface is located.The interface must be configured with an IPv6 address before the OSPFv3 interface can be enabled, otherwise it will prompt: % OSPFv3: IPV6 is not enabled on this interface R1 (config-if)#ipv6 ospf heUo-interval 5 Modify the OSPFv3 Hello interval R1 ( config-if)#ipv6 ospf dead-interval 20 Modify OSPFv3 Dead time(2)Configure Router R2 R2(config)#ipv6 unicast-routing R2(config)#ipv6 routerospf 1R2(config-rtr)#router-id 2.1.2.2 R2(config-rtr)#auto-cost reference-bandwidth 1000 R2(config-rtr)#passive-interface GigabitEthernetO/1 Configure the passive interface R2(config-rtr)#exitR2(config)#interface GigabitEthernet0/0 R2(config-if)#ipv6 address 2018:2340::2/64 R2(config-if)#ipv6 ospf 1 area 0 R2(config-if)#ipv6 ospf priority 20 Modify the interface priority to control DR election, default is 1 R2(config-if)#exit R2(config)#interface GigabitEthernetO/1 R2(config-if)#ipv6 address 2019:2222::2/64 R2( config-if)#ipv6 ospf 1 area 0 R2(config-if)#exit R2(config)#interface Serial0/0/0 R2(config-if)#ipv6 address 2017:1212::2/64 R2(conhg-if)# ipv6 ospf 1 area 0 R2(config-if)#ipv6 ospf hello-interval 5 R2(config-if)#ipv6 ospf dead-interval 20(3) Configure router R3 R3(config)#ipv6 unicast-routing R3(config)#ipv6 routerospf 1 R3(config-rtr)#router-id 3.33.3 R3 (config-rtr)#passive-interface GigabitEthernetO/1 R3(config-rtr)#auto-cost reference-bandwidth 1000 R3(config-rtr)#exit R3(config)#interface GigabitEthernet0/0 R3( config-if)#ipv6 address 2018:2340::3/64 R3(config-if)#ipv6 ospf 1 area 0 R3(config-if)#ipv6 ospf priority 10 R3(config-if)#exit R3(config)# interface GigabitEthernetO/1 R3(config-if)#ipv6 address 2019:3333=3/64 R3(config-if)#ipv6 ospf 1 area 0 R3(config-if)^xit (4) Configuring Router R4 R4(config )#ipv6 unicast-routing R4(config)#ipv6 router ospf1 R4(config-rtr)#router-id 4.4.4.4 R4(config-rtr)#auto-cost reference-bandwidth 1000 R4( config-rtr)#passive-iiiterface GigabitEthernetO/1 R4(config-rtr)#exit